Skip to content

Operating a microgrid with photovoltaics and small wind power

RXLea
Digital projects for hands-on learningInteractive learning content, directly connected to the training system.

Operating a microgrid with photovoltaics and small wind power

EPH42PT

Modular training system for hybrid island grids: learners control the energy management of PV and wind power and emulate wind and solar profiles in the lab.

Learning Content
  • Commissioning the system
  • Determining controller efficiency
  • Analyzing microgrid behavior
  • Investigating charging prioritization
KEY FEATURES
  • Evaluating wind and PV data together
  • Emulating wind profiles
  • Testing the overspeed protection of the wind charge controller
  • Emulating solar profiles
Speak with a Product Specialist +1 (757) 808-5696 · sales@lucas-nuelle.com

Self-sufficient microgrids reliably supply remote consumers and increase self-consumption without CO2 emissions. Anyone setting them up must bring together the fundamentals of wind power, the characteristics of permanent-magnet synchronous generators and charge management. For this purpose, the training system couples a synchronous generator with a rated voltage of 12 V to a servo test system that follows programmable wind profiles, and adds a solar array simulator, a hybrid inverter and two charge controllers. Learners commission the system, measure the generator output at varying speeds and log the power flows of wind power, PV and battery in the SCADA logger. They check both charge controllers close to the end-of-charge voltage and test the braking function of the wind charge controller.

CO3301-3ECapacitive load, three-phase, 1kW
SE2683-1MSynchronous generator 12V for small wind power plant with permanent magnets
CO3208-1UHybrid Inverter
CO3208-4VSolar panel emulator, 1,5kW, 80V
CO3208-1WSolar accumulator, 122Ah, 12V
CO3301-3FVariable Ohmic load, three-phase, 1kW
CO3301-5PPower switch module
CO3208-4LLamp board 230V
SO2800-3PInteractive Lab Assistant: Renewable Energies Hybrid System
SO4001-3HSoftware SCADA Viewer
CO3212-5VThree-phase power supply with motor protection switch
CO5127-2SPower Quality Meter mit Grafikdisplay und Langzeitspeicher
CO5127-2APower-Multimeter
CO3208-1XSolar module with adjustable angle of inclinationoptional
SO5148-2BSet of safety measurement cables 4mm, 10m, 4 pcsoptional
CO3208-3FSmall-scale wind turbine 370W, with demonstration mastoptional
CO3208-3GMast set for small-scale wind turbineoptional
LM9057Patch cable Cat5E 1x 1m yellow, 2x 2m yellow
LM99885-Port Ethernet Switch
LM8257USB 2.0 Ethernet adapter, 10/100
CO3636-6YServo machine test stand for 1kW machines incl. software ActiveServo (D,GB,F,E)
SE2662-7DCoupling guard with LED lighting for 1kW machines
SE2662-6ARubber coupling sleeve, 1kW
ST7200-7ASybaPro experiment trolley, 3-level, 6 sockets, 1250x1970x800mm
ST8010-4TMonitor holder for flat screen monitor of weight up to 15kg / 33lbs
ST7200-5LProtection cover for three-level experiment trolleys
ST8010-4GKeyboard adapter for flat screen monitor holders
ST8000-4FDisplay for Photovoltaic Advanced equipment
SO5126-3RSafety connecting plug 4mm with tap (2x), black, 1000V/32A CAT II
SO5126-3WSafety connecting plug 4mm with tap (2x), green/yellow, 1000V/32A CAT II
SO5126-3USafety connecting plug 4mm with tap (2x), red, 1000V/32A CAT II
SO5126-3VSafety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II
SO5148-1LSet of safety measurement cables, 4mm (31 leads)

Learning Content in Detail

Learners set up the hybrid island grid, measure the output of both generators and check the control behavior and protective devices.

Commissioning the system

Learners install a photovoltaic hybrid system with a small wind turbine.

Determining controller efficiency

Learners measure the electrical generator output at varying speeds.

Analyzing microgrid behavior

Learners log the power flows of wind power, PV and battery in the island grid.

Investigating charging prioritization

Learners check the control behavior of both battery charge controllers close to the end-of-charge voltage.

Testing safety devices

Learners monitor the braking function of the wind charge controller via the integrated load resistors.

Features & Applications

The experiments deal with decentralized power supply, hybrid island grids, renewable generation technology and load management in the microgrid.
  • Evaluating wind and PV data together — The integrated SCADA logger combines the measurement data from wind and PV generation. This allows learners to see how loads shift between the generators.
  • Emulating wind profiles — Programmable wind profiles can be reproduced via the servo drive. Learners analyze the generated power as a function of load in the lab.
  • Testing the overspeed protection of the wind charge controller — When the battery is full, the wind charge controller diverts the surplus energy into load resistors and protects the generator from overspeed. Learners trigger this condition deliberately.
  • Emulating solar profiles — Programmable solar profiles can be specified via the DC supply. Learners use them to analyze MPP tracking.
  • Servo test system CO3636-6X — The test system operates with speed control in all four quadrants, thus simulating real wind profiles.
  • Solar array simulator CO3208-4V — The simulator emulates a short-circuit-proof 1.5 kW solar array, including partial shading, for laboratory use.
  • Hybrid inverter CO3208-1U — The parameterizable inverter coordinates energy distribution between PV, battery, wind power and the AC grid.
  • Wind turbine charge controller CO3208-3E — The module contains 300 W load resistors for braking the wind generator and controls battery charging in the DC grid.
  • Synchronous generator SE2683-1M — The generator delivers a rated voltage of 12 V at an output of 0.3 kW and transmits its motor data via an electronic nameplate.
  • SCADA Viewer — The tool visualizes the interconnected grid live and logs all variables in the integrated logger. The data can be exported for further processing.
  • Wind Control Center virtual instrument — Learners control the wind turbine, load wind profiles and log both mechanical and electrical measurement data live in the integrated logger.
  • Solar Panel — Learners configure the solar array simulator, emulate solar path profiles over time and simulate partial shading of individual modules.
Learners working with RXLea on a tablet at a Lucas-Nuelle training system
RXLea

From Knowledge Comes Capability.

You guide the learning

Where theory and practice go hand in hand.

RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.

Hands-on and interactive

Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.

Digital support

3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.

Visual support

Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.

Learners using a tablet at an energy training system
RXLea on desktop, laptop and tablet
RXLea Path Creator for building learning journeys
RXLea Navigator showing the learning world
Learn more about RXLea
Newsletter

Stay ahead in
technical training.

Get the latest training systems, product launches and educational insights, delivered directly to your inbox.

Your email address

By subscribing, you agree to our Privacy Policy. You can unsubscribe at any time.

 Please select at least one category before subscribing.
I'm interested in - select all that apply