Skip to content

Coaxial Cables

RXLea
Digital projects for hands-on learningInteractive learning content, directly connected to the training system.

Coaxial Cables

TLT02UT

UniTrain training system for coaxial lines: students determine the line parameters with Wheatstone, Wien and Maxwell-Wien bridges, measure pulse propagation times and observe reflections caused by mismatch.

Learning Content
  • Determining line resistance
  • Measuring capacitance and inductance per unit length
  • Determining characteristic impedance
  • Measuring pulse propagation times
KEY FEATURES
  • RLC Measuring Bridge plug-in card
  • Pulse Generator plug-in card
  • Coaxial lines experiment module
  • Building a modular RLC measuring bridge
Speak with a Product Specialist +1 (757) 808-5696 · sales@lucas-nuelle.com

An incorrectly terminated coaxial cable reflects the signal back and distorts the transmission. This UniTrain training system demonstrates the relationship at the measuring station. Students use switches to configure the RLC measuring bridge as a Wheatstone, Wien or Maxwell-Wien bridge, balance it using precision potentiometers and thus determine the resistance, capacitance and inductance per unit length. From these, they calculate the characteristic impedance and the propagation velocity. They then feed needle pulses into cable sections with taps at 20 m, 40 m and 60 m and measure the propagation times on the oscilloscope. Using open-circuit, short-circuit and matched terminations, they compare the reflected pulses and identify the reflection-free operating condition.

CO4204-9GCourse Coaxial cables
CO4203-2AUniTrain Interface mit virtuellen Instrumenten (Basis VI)
CO4203-2JUniTrain measurement accessories, shunts and connection cables
CO4203-2YUniTrain storage case for one UniTrain system
CO4203-2BUniTrain Experimenter

Learning Content in Detail

Students determine the characteristic parameters of a coaxial line by measurement and relate them to the reflection behavior of the line.

Determining line resistance

Students balance a Wheatstone bridge and use it to calculate the resistance per unit length R' of the coaxial line.

Measuring capacitance and inductance per unit length

Students balance Wien and Maxwell-Wien bridges and use them to determine C' and L'.

Determining characteristic impedance

Students calculate the characteristic impedance Z0 from the primary line parameters.

Measuring pulse propagation times

Students feed needle pulses into lines 20 m, 40 m and 60 m long and determine the propagation velocity.

Analyzing reflection behavior

Students investigate pulse reflections with an open circuit and a short circuit at the end of the line and determine the phase relationship.

Correcting impedance mismatch

Students terminate the cable with its characteristic impedance and check reflection-free signal transfer on the oscilloscope.

Features & Applications

The experiments address questions from high-frequency and telecommunications engineering, as well as from circuit development and high-frequency measuring bridges.
  • RLC Measuring Bridge plug-in card — Provides adjustment potentiometers for precise balancing and switching elements for configuration as a Wheatstone, Wien or Maxwell-Wien bridge for DC and AC measurements.
  • Pulse Generator plug-in card — Generates needle pulses at repetition frequencies of 100 kHz and 200 kHz for measuring pulse propagation times and reflection points.
  • Coaxial lines experiment module — Contains coaxial cable segments with taps at 20 m, 40 m and 60 m for investigating length-dependent propagation times and line parameters.
  • Building a modular RLC measuring bridge — The bridge can be configured as a Wheatstone, Wien or Maxwell-Wien bridge using switches and balanced with precision potentiometers.
  • Coaxial cable measuring accessories and terminating resistors — Contains BNC connecting cables, T-pieces and defined terminating resistors for the open-circuit, short-circuit and matched conditions.
  • UniTrain interface — Supplies the measurement setups with safety extra-low voltage and provides analog measurement channels with BNC and 2 mm connections for high-frequency signals.
  • 2/4-channel oscilloscope — Captures forward and reflected pulses in X/T mode, allows bridge balancing in XY mode and measures propagation times using cursors.
  • Pulse generator — Delivers unipolar or bipolar square-wave pulses with pulse widths from 0 to 100 percent and frequencies from 0.5 Hz to 5 MHz for propagation time measurements.
  • Bode plotter — Records frequency responses and supports the determination of attenuation and phase delay over the cable length.
  • Determining the primary line parameters with a measuring bridge — Students determine the resistance per unit length R', capacitance per unit length C' and inductance per unit length L' of the coaxial line using Wheatstone, Wien and Maxwell-Wien bridges.
  • Measuring characteristic impedance and propagation velocity — Students determine the characteristic impedance by measurement and use it to calculate the propagation velocity of electromagnetic waves.
  • Investigating pulse propagation time and line reflections — Students feed needle pulses into coaxial line segments, measure the propagation times on the oscilloscope and analyze fault locations in the event of mismatch.
  • Matching and reflection-free termination — Students terminate the end of the line with a short circuit, an open circuit and the characteristic impedance and observe how the reflected pulses change as a result.
Learners working with RXLea on a tablet at a Lucas-Nuelle training system
RXLea

From Knowledge Comes Capability.

You guide the learning

Where theory and practice go hand in hand.

RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.

Hands-on and interactive

Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.

Digital support

3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.

Visual support

Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.

Learners using a tablet at an energy training system
RXLea on desktop, laptop and tablet
RXLea Path Creator for building learning journeys
RXLea Navigator showing the learning world
Learn more about RXLea
Newsletter

Stay ahead in
technical training.

Get the latest training systems, product launches and educational insights, delivered directly to your inbox.

Your email address

By subscribing, you agree to our Privacy Policy. You can unsubscribe at any time.

 Please select at least one category before subscribing.
I'm interested in - select all that apply