Skip to content

Four-Wire Lines

RXLea
Digital projects for hands-on learningInteractive learning content, directly connected to the training system.

Four-Wire Lines

TLT01UT

UniTrain training system for four-wire lines: students determine the per-unit-length line parameters with the RLC measuring bridge, measure characteristic impedance and pulse propagation times, and investigate crosstalk between the wire pairs.

Learning Content
  • Determining line resistance
  • Measuring capacitance and inductance per unit length
  • Determining characteristic impedance
  • Measuring pulse propagation times
KEY FEATURES
  • Determining the primary line parameters by measurement
  • Measuring frequency-dependent characteristic impedance
  • Analyzing pulse propagation time and wave propagation
  • Investigating near-end and far-end crosstalk
Speak with a Product Specialist +1 (757) 808-5696 · sales@lucas-nuelle.com

In a star-quad cable, several wire pairs lie close together. How strongly they influence each other determines the transmission quality. This UniTrain training system makes this measurable. Students use switches to configure the RLC measuring bridge as a Wheatstone, Wien or Maxwell-Wien bridge, balance it using precision potentiometers and thus determine the frequency-dependent resistance, inductance, capacitance and leakage conductance per unit length. Between 300 Hz and 1 MHz, they determine the characteristic impedance and propagation constant and use these to assess broadband suitability. Using needle pulses, they measure the propagation times in the pair conductors and against the shield. Finally, they determine near-end and far-end crosstalk via the coupling attenuation.

CO4204-9FCourse Telecommunications 4: Four-wire lines
CO4203-2AUniTrain Interface mit virtuellen Instrumenten (Basis VI)
CO4203-2JUniTrain measurement accessories, shunts and connection cables
CO4203-2YUniTrain storage case for one UniTrain system
CO4203-2BUniTrain Experimenter

Learning Content in Detail

Students fully characterize a four-wire line: from the primary line parameters and the characteristic impedance to reflection and crosstalk behavior.

Determining line resistance

Students balance a Wheatstone bridge and use it to calculate the resistance per unit length R'.

Measuring capacitance and inductance per unit length

Students balance Wien and Maxwell-Wien bridges and use them to determine C' and L'.

Determining characteristic impedance

Students calculate the characteristic impedance Z0 from the primary line parameters.

Measuring pulse propagation times

Students feed needle pulses into line sections of different lengths and determine the propagation velocity.

Analyzing reflection behavior

Students investigate pulse reflections with an open circuit and a short circuit at the end of the line and determine the phase relationship.

Correcting impedance mismatch

Students terminate the line with its characteristic impedance and check reflection-free signal transfer on the oscilloscope.

Features & Applications

The experiments address questions from telecommunications and broadband transmission technology, as well as from high-frequency engineering and cable diagnostics.
  • Determining the primary line parameters by measurement — Students determine the frequency-dependent resistance, inductance, capacitance and leakage conductance per unit length of the four-wire line using the electrically isolated RLC measuring bridge.
  • Measuring frequency-dependent characteristic impedance — Students determine the characteristic impedance and propagation constant between 300 Hz and 1 MHz and use them to assess the line’s broadband suitability.
  • Analyzing pulse propagation time and wave propagation — Using needle pulses, students determine the propagation velocity and measure the signal propagation times in the pair conductors and between pair conductor and shield.
  • Investigating near-end and far-end crosstalk — Students analyze the capacitive and inductive coupling between the wire pairs of the star-quad cable and determine near-end and far-end crosstalk via the attenuation.
  • Changing the bridge circuit at the flick of a switch — The RLC measuring bridge can be switched to operate as a Wheatstone, Wien or Maxwell-Wien bridge. Balancing is carried out using precision potentiometers.
  • RLC Measuring Bridge plug-in card — Contains switchable bridge arms and electrical isolation for measuring resistance, capacitance and inductance per unit length.
  • Pulse Generator plug-in card — Generates needle pulses at repetition frequencies of 100 kHz and 200 kHz for measuring pulse propagation times and reflection points.
  • Four-Wire Lines experiment module — Contains a 100 m and a 5 m four-wire line in star-quad configuration. The wires are individually accessible, so that line properties and crosstalk can be investigated.
  • Precision potentiometers for bridge balancing — Students balance the bridge precisely and read the resulting resistance value directly on the adjustment scale, without additional measuring instruments.
  • 2/4-channel oscilloscope — Captures forward and reflected pulses in X/T mode, allows the bridge to be balanced using Lissajous figures in XY mode and measures propagation times using cursors.
  • UniTrain interface — Supplies the measurement setups with safety extra-low voltage and provides analog measurement channels with BNC and 2 mm connections for high-frequency signals.
  • Bode plotter — Records frequency responses and supports the determination of attenuation and phase delay over the cable length.
Learners working with RXLea on a tablet at a Lucas-Nuelle training system
RXLea

From Knowledge Comes Capability.

You guide the learning

Where theory and practice go hand in hand.

RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.

Hands-on and interactive

Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.

Digital support

3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.

Visual support

Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.

Learners using a tablet at an energy training system
RXLea on desktop, laptop and tablet
RXLea Path Creator for building learning journeys
RXLea Navigator showing the learning world
Learn more about RXLea
Newsletter

Stay ahead in
technical training.

Get the latest training systems, product launches and educational insights, delivered directly to your inbox.

Your email address

By subscribing, you agree to our Privacy Policy. You can unsubscribe at any time.

 Please select at least one category before subscribing.
I'm interested in - select all that apply