Skip to content

Measurement Technology: Non-Electric Values T/P/F

RXLea
Digital projects for hands-on learningInteractive learning content, directly connected to the training system.

Measurement Technology: Non-Electric Values T/P/F

IMT02UT

Compact UniTrain training system for industrial sensor technology: learners record the characteristics of NTC, Pt-100 and KTY sensors, a thermocouple, pressure transducers and strain gauges, then amplify and linearize the signals.

Learning Content
  • Adjusting the measuring amplifier
  • Characterizing NTC thermistors
  • Linearizing NTC characteristics
  • Comparing Pt-100 connection methods
KEY FEATURES
  • Reproducible temperature characteristics up to 80 °C
  • Lead compensation with 2-, 3- and 4-wire connections
  • Piezoresistive analysis of absolute and differential pressure
  • Mechanical force analysis on a strain gauge bending beam
Speak with a Product Specialist +1 (757) 808-5696 · sales@lucas-nuelle.com

Process monitoring and quality control begin at the point where a physical quantity becomes an electrical signal. Temperature, pressure, force and torque, however, produce small, often non-linear voltages, and lead resistances distort the result further. The UniTrain system makes this chain easy to follow using real sensors. Three experiment cards carry NTC, Pt-100 and KTY sensors and a type J thermocouple, piezoresistive absolute and differential pressure sensors, and a bending beam and torsion bar with strain gauges. Learners adjust the instrumentation amplifier, record characteristics with the virtual XY recorder and compare 2-, 3- and 4-wire connections. By the end, they are able to select sensors, wire them up and evaluate their measurement results.

CO4204-8BCourse Measurement technology 2: Non-electric values T/P/F
LM2330Multi13S digital multimeter
SO4203-2YUniTrain storage case for one systemoptional
CO4203-2AUniTrain Interface mit virtuellen Instrumenten (Basis VI)
CO4203-2JUniTrain measurement accessories, shunts and connection cables
CO4203-2YUniTrain storage case for one UniTrain system
CO4203-2BUniTrain Experimenter

Learning Content in Detail

Learners work through the entire measuring chain: recording sensor characteristics, amplifying small signals, correcting non-linear behavior and evaluating the results themselves.

Adjusting the measuring amplifier

Learners adjust the gain and offset of the instrumentation amplifier for minimum zero drift.

Characterizing NTC thermistors

Learners record exponential resistance characteristics and calculate time constants and half-lives.

Linearizing NTC characteristics

Learners connect compensation resistors in parallel and optimize the linear transfer behavior.

Comparing Pt-100 connection methods

Learners compare 2-, 3- and 4-wire connections and eliminate the influence of lead resistances.

Evaluating KTY sensors

Learners operate silicon temperature sensors in Wheatstone bridges using the deflection method.

Using thermocouples

Learners measure thermoelectric voltages on Fe-CuNi thermocouples and apply mathematical and automatic cold junction compensation.

Measuring absolute and differential pressure

Using the hand pump, learners determine the static characteristics of piezoresistive pressure transducers.

Measuring force on a bending beam

Learners investigate strain gauges in quarter-, half- and full-bridge configurations under various weight loads.

Determining torque on a torsion bar

Learners measure direction-dependent shear stresses using 45° strain gauge half-bridges.

Features & Applications

The experiments address tasks from measurement and control engineering, from electrical power engineering including grid monitoring, and from industrial maintenance and test bay practice.
  • Reproducible temperature characteristics up to 80 °C — An integrated PI controller and a heating transistor with an LM35 reference sensor bring the heating plate to defined temperatures. This allows learners to record characteristics reproducibly and repeat series of measurements.
  • Lead compensation with 2-, 3- and 4-wire connections — Learners investigate how parasitic lead resistances in Pt-100 measurements can be completely eliminated by circuit design, comparing the three connection methods side by side.
  • Piezoresistive analysis of absolute and differential pressure — Using a hand pump and a calibrated pressure gauge, learners precisely record the characteristics of absolute and differential pressures up to 400 mbar.
  • Mechanical force analysis on a strain gauge bending beam — Quarter-, half- and full-bridge circuits are compared on the bending beam. Learners determine the effect of the force and see how sensitivity increases with the bridge configuration.
  • Temperature measurement experiment card (SO4203-5R) — The card contains NTC, PTC (Pt-100) and KTY sensors and a type J thermocouple, plus a heating plate with an LM35 sensor and switchable lead and linearization resistors.
  • Pressure measurement experiment card (SO4203-5S) — An absolute pressure sensor and a differential pressure sensor with integrated resistance measuring bridges capture the pressure signal.
  • Force and torque measurement experiment card (SO4203-5T) — A bending beam with four strain gauges allows quarter-, half- and full-bridge configurations. The torsion bar with two strain gauges and a double weighing pan is used for torque measurement.
  • Hand pump with pressure gauge — The hand pump generates defined test pressures and displays the applied value, so learners can apply specific pressures to the pressure sensors.
  • Virtual oscilloscope — Two channels display the waveforms of current, voltage and instantaneous power over time in X/T mode.
  • Waveform generator — The generator produces synthetic and mathematically defined waveforms that can be used to investigate deviations of the meter movements.
  • Virtual XY recorder — The recorder automatically records sensor characteristics across voltage and temperature curves and shows non-linearities in real time.
Learners working with RXLea on a tablet at a Lucas-Nuelle training system
RXLea

From Knowledge Comes Capability.

You guide the learning

Where theory and practice go hand in hand.

RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.

Hands-on and interactive

Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.

Digital support

3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.

Visual support

Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.

Learners using a tablet at an energy training system
RXLea on desktop, laptop and tablet
RXLea Path Creator for building learning journeys
RXLea Navigator showing the learning world
Learn more about RXLea
Newsletter

Stay ahead in
technical training.

Get the latest training systems, product launches and educational insights, delivered directly to your inbox.

Your email address

By subscribing, you agree to our Privacy Policy. You can unsubscribe at any time.

 Please select at least one category before subscribing.
I'm interested in - select all that apply