Design of Photovoltaic Systems for Grid-Parallel Operation
Design of Photovoltaic Systems for Grid-Parallel Operation
Training system for grid-connected photovoltaics: learners install the system with an industrial inverter, feed power into the grid and investigate the disconnection behavior in the event of a fault using reproducible solar simulation.
- Setting up and commissioning a grid-connected PV system
- Comparing self-consumption and full feed-in
- Determining inverter efficiency
- Verifying the response to grid faults
- Reproducible solar simulation in the lab
- Industrial components in a protected lab setting
- PV grid inverter CO3208-1S with grid monitoring
- Digital energy monitor CO3208-2T
Photovoltaic systems only feed into the grid reliably if installation, commissioning and grid monitoring are right. This cannot be practiced on a roof, because the sun and the grid do not wait for lessons. The training system therefore replicates the installation in the lab: an industrial PV inverter with grid monitoring, a triple solar module emulator, an energy monitor and lamp boards for self-consumption. Irradiance and the course of the sun can be set, so every group measures under the same conditions. Learners set up the system, commission it, balance the energy flows between generator, consumers and grid, and verify disconnection from the grid via the automatic disconnection device.
| Base Product | |
| CO3208-4L | Lamp board 230V |
| CO3208-1S | Industrial photovoltaic inverter |
| CO3111-1A | Power supply single phase with switch, circuit breaker and Schuko socket |
| CO3208-2T | Energy monitor |
| SO2800-6Q | Interactive Lab Assistant: Photovoltaic systems - Advanced course |
| CO3208-1A | Solar module simulation model, 3-fold, 23V / 2A |
| Measuring Instruments | |
| CO5127-2A | Power-Multimeter |
| Options | |
| CO3208-1X | Solar module with adjustable angle of inclinationoptional |
| SO5148-2B | Set of safety measurement cables 4mm, 10m, 4 pcsoptional |
| Furniture | |
| ST7200-7A | SybaPro experiment trolley, 3-level, 6 sockets, 1250x1970x800mm |
| ST8010-4T | Monitor holder for flat screen monitor of weight up to 15kg / 33lbs |
| ST7200-5L | Protection cover for three-level experiment trolleys |
| ST8010-4G | Keyboard adapter for flat screen monitor holders |
| Furniture Accessories | |
| ST8000-4F | Display for Photovoltaic Advanced equipment |
| Measurement Leads | |
| SO5126-3R | Safety connecting plug 4mm with tap (2x), black, 1000V/32A CAT II |
| SO5126-3U | Safety connecting plug 4mm with tap (2x), red, 1000V/32A CAT II |
| SO5126-3V | Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II |
| SO5126-3W | Safety connecting plug 4mm with tap (2x), green/yellow, 1000V/32A CAT II |
| SO5148-1L | Set of safety measurement cables, 4mm (31 leads) |
| SO5126-8K | Safety measurement cable 4mm, 50cm/20", red, 600 V CAT III ~1000V, CAT II / 32 A |
Learning Content in Detail
Setting up and commissioning a grid-connected PV system
Comparing self-consumption and full feed-in
Determining inverter efficiency
Verifying the response to grid faults
Features & Applications
- Reproducible solar simulation in the lab — Electronic solar module emulators specify irradiance and the course of the sun. As a result, every group measures under identical conditions, and partial shading or yield fluctuations become directly measurable.
- Industrial components in a protected lab setting — The system works with genuine feed-in components of the kind installed in building services and energy engineering. At the same time, the lab setup remains protected against incorrect wiring and overload.
- PV grid inverter CO3208-1S with grid monitoring — The inverter features a grid monitoring device. Learners use it to observe the prescribed disconnection behavior and the prevention of unintentional islanding during operation.
- Digital energy monitor CO3208-2T — The measuring instrument captures voltage, current and apparent, active and reactive power simultaneously and shows them on a backlit graphic display. From these values, learners determine efficiencies and the ratio of generation, self-consumption and feed-in.
- Solar module emulator CO3208-1A for system experiments — Three independently adjustable modules make the experiments independent of real sunlight. Learners vary the irradiance, connect modules in series and in parallel, simulate partial shading and test switchable bypass diodes against hot spots.

From Knowledge Comes Capability.
You guide the learning
Where theory and practice go hand in hand.
RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.
Hands-on and interactive
Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.
Digital support
3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.
Visual support
Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.




Stay ahead in
technical training.
Get the latest training systems, product launches and educational insights, delivered directly to your inbox.