Skip to content

Automatically separate workpieces and feed them to the conveyor system

RXLea
Digital projects for hands-on learningInteractive learning content, directly connected to the training system.

Automatically separate workpieces and feed them to the conveyor system

CIS03IS

Mechatronic subsystem for IMS and IMU conveyor systems: Learners separate workpiece bases from a stack magazine, feed them onto the workpiece carrier, and program the sequence control in the TIA Portal.

Learning Content
  • Analyzing the separation process
  • Controlling pneumatic valves
  • Evaluating sensor signals
  • Designing sequential controls
KEY FEATURES
  • Automated material separation
  • Controlling the pneumatic pawl
  • Monitoring the magazine fill level
  • Locking the workpiece carrier pneumatically
Speak with a Product Specialist +1 (757) 808-5696 · sales@lucas-nuelle.com

Separating and feeding workpieces are fundamental process steps in automated production systems. With this subsystem, learners put this process into practice by programming the control sequence, monitoring the process, and testing it directly on the conveyor system. A pneumatic stopper positions the workpiece carrier beneath the stack magazine. A pneumatically actuated latch then releases one workpiece base at a time. A limit switch monitors the magazine fill level, while a cylinder sensor detects the upper position of the stopper. All signals are transmitted to the conveyor system PLC via a 25-pin D-sub connector.

In the TIA Portal, learners program the sequence control as a step sequence and logically link sensor feedback with the actuators. They then verify the programmed sequence directly on the real conveyor system. In this way, they develop practical skills in valve control, state-based sequence control in accordance with EN 61131-3, and systematic troubleshooting of sensors and actuators.

LM9515Cyber physical conveyor system with PLC
SO6200-2PQuickChart IMS 1.5 Cyber-physical conveyor belt system
LM9532Film, for oscilloscope cameratype LM 7000
LM9672DC power supply 24V/5A for IMS conveyor belts
LM9627Sorting station
LM9066Interface cable 25-pin, Sub-D socket / plug 1m
SO6200-1CQuickChart, IMS 3 Mechatronics Sorting sub-system
PAT050001CRXLea Content CIS01IS: Inbetriebnahme eines cyberphysischen Systems
SW00019Software LN Installer
SW00001Software RX Lea
PAT050002CRXLea Content CIS01IS: Grundlagen der SPS Programmierung
SW00019Software LN Installer
SW00001Software RX Lea
PAT050003CRXLea Content CIS01IS: Geschwindigkeitskontrolle mit PWM
SW00019Software LN Installer
SW00001Software RX Lea
PAT050004CRXLea Content CIS01IS: Analogwertverarbeitung in der SPS
SW00001Software RX Lea
SW00019Software LN Installer
SO2805-5XInteractive Lab Assistant: Self-commutated converter circuits
LM9677IMS displacement measurement module
LM8257USB 2.0 Ethernet adapter, 10/100
LM9716Set of Allen keys
LM9524Workpiece, bottom section, white
LM9525Workpiece, bottom section, black
ST7200-7ASybaPro experiment trolley, 3-level, 6 sockets, 1250x1970x800mm
ST8010-4TMonitor holder for flat screen monitor of weight up to 15kg / 33lbs
ST7200-5LProtection cover for three-level experiment trolleys

Learning Content in Detail

Learners work through the separation process from pneumatics and sensor evaluation to structured sequential control and troubleshooting in the TIA Portal.

Analyzing the separation process

Learners analyze the mechanical and pneumatic sequence involved in separating workpieces in an orderly manner.

Controlling pneumatic valves

Learners program 3/2-way and 4/2-way solenoid valves to move the stopper and pawl.

Evaluating sensor signals

Learners process feedback from cylinder switches and fill level sensors logically in the controller.

Designing sequential controls

Learners create state-based step sequences in accordance with EN 61131-3 and use them to coordinate the belt and station.

Integrating fill level logic

Learners program protective queries that safely interrupt the production process when the magazine is empty.

Structuring function blocks

Learners encapsulate the station logic in reusable function blocks with defined interfaces.

Coupling interfaces

Learners connect the I/O signals of the subsystem to the PLC via the 25-pin Sub-D interface.

Diagnosing faults systematically

Learners systematically locate signal faults on sensors and actuators in the TIA Portal.

Features & Applications

The subsystem brings together three subject areas: automation technology, mechatronics and production engineering, and pneumatics and control technology.
  • Automated material separation — The subsystem takes workpiece bottom parts from the stack magazine in an orderly manner and transfers them to the workpiece carrier in precise timing with the cycle.
  • Controlling the pneumatic pawl — A 3/2-way solenoid valve controls the ejector pawl, which releases exactly one workpiece at a time via the separator.
  • Monitoring the magazine fill level — A mechanical limit switch detects the magazine fill level and prevents startup attempts when the supply container is empty.
  • Locking the workpiece carrier pneumatically — A 4/2-way solenoid valve lowers the stopper and stops the workpiece carrier exactly beneath the magazine.
  • Connection via the 25-pin Sub-D connector — The Sub-D connector links the subsystem directly to the conveyor belt and the higher-level PLC control.
  • Stack magazine for bottom parts — The magazine holds block bottom parts or model car bodies and feeds them to the separating mechanism.
  • 3/2-way solenoid valve for the pawl — The valve actuates the pneumatic ejector, which separates the lowest workpiece from the stack magazine.
  • 4/2-way solenoid valve for the stopper — The valve lowers the mechanical stopper of the conveyor line and stops the workpiece carrier with pinpoint accuracy.
  • Cylinder switch: stopper up — The switch signals the upper end position of the stopper to the PLC as the enabling condition for belt movement.
  • Limit switch for the magazine fill level — The limit switch checks whether there are components in the magazine and automatically stops the process chain if material runs out.
  • 25-pin transfer module — The module bundles all I/O signals from the sensors and actuators and connects them to the controller with reverse-polarity protection.
  • Pneumatic maintenance interface — The 0.5 MPa compressed air supply is connected via standardized 4 mm push-in fittings.
  • Siemens TIA Portal — Learners program step sequences in FBD or ST, manage variables and test the station’s sequential control.
  • Interactive Lab Assistant course SO2805-5X — The interactive learning software contains 3D system models, circuit diagrams, instructions on step sequences and automatic knowledge tests.
Learners working with RXLea on a tablet at a Lucas-Nuelle training system
RXLea

From Knowledge Comes Capability.

You guide the learning

Where theory and practice go hand in hand.

RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.

Hands-on and interactive

Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.

Digital support

3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.

Visual support

Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.

Learners using a tablet at an energy training system
RXLea on desktop, laptop and tablet
RXLea Path Creator for building learning journeys
RXLea Navigator showing the learning world
Learn more about RXLea
Newsletter

Stay ahead in
technical training.

Get the latest training systems, product launches and educational insights, delivered directly to your inbox.

Your email address

By subscribing, you agree to our Privacy Policy. You can unsubscribe at any time.

 Please select at least one category before subscribing.
I'm interested in - select all that apply