Operating a microgrid with photovoltaics and small wind power
Operating a microgrid with photovoltaics and small wind power
Modular training system for hybrid island grids: learners control the energy management of PV and wind power and emulate wind and solar profiles in the lab.
- Commissioning the system
- Determining controller efficiency
- Analyzing microgrid behavior
- Investigating charging prioritization
- Evaluating wind and PV data together
- Emulating wind profiles
- Testing the overspeed protection of the wind charge controller
- Emulating solar profiles
Self-sufficient microgrids reliably supply remote consumers and increase self-consumption without CO2 emissions. Anyone setting them up must bring together the fundamentals of wind power, the characteristics of permanent-magnet synchronous generators and charge management. For this purpose, the training system couples a synchronous generator with a rated voltage of 12 V to a servo test system that follows programmable wind profiles, and adds a solar array simulator, a hybrid inverter and two charge controllers. Learners commission the system, measure the generator output at varying speeds and log the power flows of wind power, PV and battery in the SCADA logger. They check both charge controllers close to the end-of-charge voltage and test the braking function of the wind charge controller.
| Base Product | |
| CO3301-3E | Capacitive load, three-phase, 1kW |
| SE2683-1M | Synchronous generator 12V for small wind power plant with permanent magnets |
| CO3208-1U | Hybrid Inverter |
| CO3208-4V | Solar panel emulator, 1,5kW, 80V |
| CO3208-1W | Solar accumulator, 122Ah, 12V |
| CO3301-3F | Variable Ohmic load, three-phase, 1kW |
| CO3301-5P | Power switch module |
| CO3208-4L | Lamp board 230V |
| SO2800-3P | Interactive Lab Assistant: Renewable Energies Hybrid System |
| Software | |
| SO4001-3H | Software SCADA Viewer |
| Power Supply | |
| CO3212-5V | Three-phase power supply with motor protection switch |
| Measuring Instruments | |
| CO5127-2S | Power Quality Meter mit Grafikdisplay und Langzeitspeicher |
| CO5127-2A | Power-Multimeter |
| Options | |
| CO3208-1X | Solar module with adjustable angle of inclinationoptional |
| SO5148-2B | Set of safety measurement cables 4mm, 10m, 4 pcsoptional |
| CO3208-3F | Small-scale wind turbine 370W, with demonstration mastoptional |
| CO3208-3G | Mast set for small-scale wind turbineoptional |
| Accessories | |
| LM9057 | Patch cable Cat5E 1x 1m yellow, 2x 2m yellow |
| LM9988 | 5-Port Ethernet Switch |
| LM8257 | USB 2.0 Ethernet adapter, 10/100 |
| CO3636-6Y | Servo machine test stand for 1kW machines incl. software ActiveServo (D,GB,F,E) |
| SE2662-7D | Coupling guard with LED lighting for 1kW machines |
| SE2662-6A | Rubber coupling sleeve, 1kW |
| Furniture | |
| ST7200-7A | SybaPro experiment trolley, 3-level, 6 sockets, 1250x1970x800mm |
| ST8010-4T | Monitor holder for flat screen monitor of weight up to 15kg / 33lbs |
| ST7200-5L | Protection cover for three-level experiment trolleys |
| ST8010-4G | Keyboard adapter for flat screen monitor holders |
| Furniture Accessories | |
| ST8000-4F | Display for Photovoltaic Advanced equipment |
| Measurement Leads | |
| SO5126-3R | Safety connecting plug 4mm with tap (2x), black, 1000V/32A CAT II |
| SO5126-3W | Safety connecting plug 4mm with tap (2x), green/yellow, 1000V/32A CAT II |
| SO5126-3U | Safety connecting plug 4mm with tap (2x), red, 1000V/32A CAT II |
| SO5126-3V | Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II |
| SO5148-1L | Set of safety measurement cables, 4mm (31 leads) |
Learning Content in Detail
Commissioning the system
Determining controller efficiency
Analyzing microgrid behavior
Investigating charging prioritization
Testing safety devices
Features & Applications
- Evaluating wind and PV data together — The integrated SCADA logger combines the measurement data from wind and PV generation. This allows learners to see how loads shift between the generators.
- Emulating wind profiles — Programmable wind profiles can be reproduced via the servo drive. Learners analyze the generated power as a function of load in the lab.
- Testing the overspeed protection of the wind charge controller — When the battery is full, the wind charge controller diverts the surplus energy into load resistors and protects the generator from overspeed. Learners trigger this condition deliberately.
- Emulating solar profiles — Programmable solar profiles can be specified via the DC supply. Learners use them to analyze MPP tracking.
- Servo test system CO3636-6X — The test system operates with speed control in all four quadrants, thus simulating real wind profiles.
- Solar array simulator CO3208-4V — The simulator emulates a short-circuit-proof 1.5 kW solar array, including partial shading, for laboratory use.
- Hybrid inverter CO3208-1U — The parameterizable inverter coordinates energy distribution between PV, battery, wind power and the AC grid.
- Wind turbine charge controller CO3208-3E — The module contains 300 W load resistors for braking the wind generator and controls battery charging in the DC grid.
- Synchronous generator SE2683-1M — The generator delivers a rated voltage of 12 V at an output of 0.3 kW and transmits its motor data via an electronic nameplate.
- SCADA Viewer — The tool visualizes the interconnected grid live and logs all variables in the integrated logger. The data can be exported for further processing.
- Wind Control Center virtual instrument — Learners control the wind turbine, load wind profiles and log both mechanical and electrical measurement data live in the integrated logger.
- Solar Panel — Learners configure the solar array simulator, emulate solar path profiles over time and simulate partial shading of individual modules.

From Knowledge Comes Capability.
You guide the learning
Where theory and practice go hand in hand.
RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.
Hands-on and interactive
Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.
Digital support
3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.
Visual support
Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.




Stay ahead in
technical training.
Get the latest training systems, product launches and educational insights, delivered directly to your inbox.