Skip to content

Automatically place and join workpiece tops

RXLea
Digital projects for hands-on learningInteractive learning content, directly connected to the training system.

Automatically place and join workpiece tops

CIS04IS

Mechatronic subsystem for IMS and IMU conveyor systems: Learners remove workpiece tops from a stack magazine, place them onto the passing workpiece bases, and program the assembly sequence in the TIA Portal.

Learning Content
  • Analyzing assembly processes
  • Controlling the assembly cylinder
  • Coordinating workpiece fixing
  • Designing step sequences
KEY FEATURES
  • Assembling modules precisely
  • Controlling the pneumatic joining pawl
  • Checking magazine filling
  • Locking the workpiece carrier precisely
Speak with a Product Specialist +1 (757) 808-5696 · sales@lucas-nuelle.com

Precise positioning and joining of components are key tasks in automated assembly processes. With this subsystem, learners carry out the assembly step in a hands-on environment, program the sequence, and test the interaction between the conveyor system, sensors, and actuators directly on the equipment. A pneumatic stopper positions the workpiece carrier beneath the station. A pneumatically actuated joining latch then places the lowest workpiece top onto the base. A limit switch monitors the occupancy of the magazine shaft, while a cylinder sensor detects the upper position of the stopper. All sensor and actuator signals are transmitted to the conveyor system PLC via the 25-pin D-sub interface module.

In the TIA Portal, learners program the assembly sequence and coordinate the stopper, conveyor stop, and joining operation. They then test the programmed process directly on the real conveyor system and analyze sequence errors. In this way, they develop practical skills in sequence control, linking sensor and actuator signals, and systematic troubleshooting.

LM9515Cyber physical conveyor system with PLC
SO6200-2PQuickChart IMS 1.5 Cyber-physical conveyor belt system
LM9532Film, for oscilloscope cameratype LM 7000
LM9672DC power supply 24V/5A for IMS conveyor belts
LM9628Assembly station
LM9066Interface cable 25-pin, Sub-D socket / plug 1m
SO6200-1DQuickChart, IMS 4 Mechatronics Assembly sub-system (GB)
PAT050001CRXLea Content CIS01IS: Inbetriebnahme eines cyberphysischen Systems
SW00001Software RX Lea
SW00019Software LN Installer
PAT050002CRXLea Content CIS01IS: Grundlagen der SPS Programmierung
SW00001Software RX Lea
SW00019Software LN Installer
PAT050003CRXLea Content CIS01IS: Geschwindigkeitskontrolle mit PWM
SW00001Software RX Lea
SW00019Software LN Installer
PAT050004CRXLea Content CIS01IS: Analogwertverarbeitung in der SPS
SW00001Software RX Lea
SW00019Software LN Installer
SO2805-5XInteractive Lab Assistant: Self-commutated converter circuits
LM9677IMS displacement measurement module
LM8257USB 2.0 Ethernet adapter, 10/100
LM9716Set of Allen keys
LM9521Workpiece, top section, white
LM9522Workpiece, top section, black
LM9524Workpiece, bottom section, white
ST7200-7ASybaPro experiment trolley, 3-level, 6 sockets, 1250x1970x800mm
ST8010-4TMonitor holder for flat screen monitor of weight up to 15kg / 33lbs
ST7200-5LProtection cover for three-level experiment trolleys

Learning Content in Detail

Learners work through the assembly process from valve control and synchronization with the belt to structured sequential control and troubleshooting.

Analyzing assembly processes

Learners analyze the joining and positioning of workpiece top parts on bottom parts.

Controlling the assembly cylinder

Learners program the solenoid valves for precise timing of the joining pawl.

Coordinating workpiece fixing

Learners synchronize lowering of the stopper and belt standstill with the assembly pulse.

Designing step sequences

Learners create sequential controls in accordance with EN 61131-3 with start, stop and reset functions.

Integrating material monitoring

Learners process fill level signals and block assembly sequences when the magazine is empty.

Creating modular function blocks

Learners structure station calls in function blocks with clearly defined transfer parameters.

Checking signal paths

Learners check the wiring and the interaction between subsystem and PLC via the Sub-D interface.

Eliminating faults in the sequence

Learners identify errors in the assembly sequence and eliminate them systematically in the code.

Features & Applications

The subsystem brings together three subject areas: automation technology, assembly technology and mechatronics, and pneumatics and control technology.
  • Assembling modules precisely — The subsystem places workpiece top parts from the stack magazine accurately onto the positioned bottom part on the workpiece carrier.
  • Controlling the pneumatic joining pawl — A 3/2-way solenoid valve controls the assembly pawl and lowers the lowest top part precisely onto the bottom part on the carrier.
  • Checking magazine filling — A mechanical limit switch detects whether there are top parts in the shaft and prevents faulty assembly when the magazine is empty.
  • Locking the workpiece carrier precisely — The pneumatic stopper holds the workpiece carrier beneath the assembly station during the pressing-on process.
  • Standardized system coupling — The 25-pin Sub-D transfer module passes all sensor and actuator signals directly to the conveyor belt’s PLC control.
  • Stack magazine for top parts — The magazine holds housing top parts or vehicle chassis and feeds them to the pneumatic assembly mechanism.
  • 3/2-way solenoid valve for assembly — The valve actuates the ejection and joining mechanism, which places the top part onto the workpiece bottom part.
  • 4/2-way solenoid valve for the stopper — The valve lowers the stopper cylinder and fixes the workpiece carrier exactly beneath the assembly position.
  • Cylinder switch: stopper up — The switch monitors the upper end position of the stopper and enables the workpiece carrier to move on.
  • Limit switch for the magazine fill level — The limit switch detects whether there are top parts in the magazine.
  • 25-pin transfer module (-X1) — The module connects the actuators and sensors of the assembly module to the controller with reverse-polarity protection.
  • Pneumatic distribution system — The distribution system supplies the solenoid valves with non-lubricated compressed air at 0.5 MPa via standard quick-release fittings.
  • Siemens TIA Portal — The development environment is used to create blocks, step sequences and signal logic for the assembly process.
  • Interactive Lab Assistant course — The interactive learning software contains animated experiment setups, rules for step sequences and knowledge tests.
Learners working with RXLea on a tablet at a Lucas-Nuelle training system
RXLea

From Knowledge Comes Capability.

You guide the learning

Where theory and practice go hand in hand.

RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.

Hands-on and interactive

Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.

Digital support

3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.

Visual support

Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.

Learners using a tablet at an energy training system
RXLea on desktop, laptop and tablet
RXLea Path Creator for building learning journeys
RXLea Navigator showing the learning world
Learn more about RXLea
Newsletter

Stay ahead in
technical training.

Get the latest training systems, product launches and educational insights, delivered directly to your inbox.

Your email address

By subscribing, you agree to our Privacy Policy. You can unsubscribe at any time.

 Please select at least one category before subscribing.
I'm interested in - select all that apply