Three-Phase Double Busbar System
Three-Phase Double Busbar System
Teach intelligent energy distribution grids: This system provides complete practical equipment. Students build, control, and analyze meshed networks with multiple feeders and consumers easily via a SCADA system.
- Planning switchgear with double busbars
- Managing operation via SCADA
- Carrying out switching operations safely
- Applying the fundamentals of protection technology
- Modular and scalable smart grid lab
- Practicing critical switching operations without risk
- Operational management: measuring and controlling via SCADA
- Processor-controlled double busbar modules
Distribution grids must be able to be switched over without loads dropping out. Switchgear with double busbars makes this possible, but requires every switching operation to be carried out in a precise sequence. This 208 V, 60 Hz version replicates a smart grid on a laboratory scale: processor-controlled double busbar bays for infeed, outgoing feeder and bus coupler, three-phase transmission line models, digital time-overcurrent relays and an adjustable three-phase power supply. Students plan grid topologies, carry out uninterrupted busbar transfers and observe currents, voltages and power in the SCADA control room. The integrated interlocking logic reports unsafe switching states.
| Base Product | |
| CO3301-5R | Double busbar unit, three-phase, incoming / outgoing feeder |
| CO3301-5S | Double busbar unit, three-phase, coupler panel |
| CO3301-3A | Transmission line Model 150km/300km (93.2miles/186.4miles) |
| CO3301-4J | Überstromzeitrelais |
| CO3301-3H | Ohmic load 3x 560 Ohm |
| CO3301-5P | Power switch module |
| SO2800-3Z7 | Interactive Lab Assistant: Smart Grid |
| SO2800-9N | Interactive Lab Assistant: Bus bar systems |
| SO2800-3L7 | Interactive Lab Assistant: High-voltage transmission lines |
| SO2800-6L7 | Interactive Lab Assistant: Protective systems for high-voltage transmission line |
| CO3301-5R | Double busbar unit, three-phase, incoming / outgoing feeder |
| CO3301-5S | Double busbar unit, three-phase, coupler panel |
| CO3301-3H | Ohmic load 3x 560 Ohm |
| SO2800-9N | Interactive Lab Assistant: Bus bar systems |
| CO3301-3A | Transmission line Model 150km/300km (93.2miles/186.4miles) |
| SO2800-3L | Interactive Lab Assistant: High-voltage transmission lines |
| Software | |
| SO4001-3F | Software SCADA for Power Engineering, designer software |
| Power Supply | |
| CO3301-3Z7 | Adjustable 3-phase power supply, 0-450V/2A |
| Measuring Instruments | |
| CO5127-2S | Power Quality Meter mit Grafikdisplay und Langzeitspeicher |
| Accessories | |
| LM9057 | Patch cable Cat5E 1x 1m yellow, 2x 2m yellow |
| LM8257 | USB 2.0 Ethernet adapter, 10/100 |
| LM9988-8 | 5-Port Ethernet Switch (International) |
| ST8010-4J8 | Multiple power outlet strip, 6 outlets, US-standard |
| LM9025 | Interface converter USB/RS485 |
| Furniture | |
| ST7200-7A7 | Mobile workstation, 3 level frame, 6 sockets, 1250x1970x800 mm, 49"x77.5"x31.5" |
| ST8010-4T | Monitor holder for flat screen monitor of weight up to 15kg / 33lbs |
| ST7200-5L | Protection cover for three-level experiment trolleys |
| ST8010-4G | Keyboard adapter for flat screen monitor holders |
| Furniture Accessories | |
| ST8000-4A | Display for Smart Grid equipment |
| Measurement Leads | |
| SO5126-3R | Safety connecting plug 4mm with tap (2x), black, 1000V/32A CAT II |
| SO5126-3V | Safety connecting plug 4mm with tap (2x), blue, 1000V/32A CAT II |
| SO5126-3W | Safety connecting plug 4mm with tap (2x), green/yellow, 1000V/32A CAT II |
| SO5148-1L | Set of safety measurement cables, 4mm (31 leads) |
| SO5126-8B | Safety measurement cable 4mm, 25cm/10", black, 600V CAT III ~1000V CAT II / 32A |
Learning Content in Detail
Planning switchgear with double busbars
Managing operation via SCADA
Carrying out switching operations safely
Applying the fundamentals of protection technology
Features & Applications
- Modular and scalable smart grid lab — The double busbar modules form the backbone of the distribution grid and can be combined to form ring or meshed grids. The lab can be extended with wind power, pumped storage, photovoltaics or complex loads.
- Practicing critical switching operations without risk — Students try out uninterrupted busbar transfer and switch loads over without a power outage. The integrated logic prevents unsafe switching states and signals operating errors visually and audibly.
- Operational management: measuring and controlling via SCADA — The hardware continuously acquires voltages and currents and passes them to the SCADA software; commands travel the same route back to the system. Ready-made interfaces are included for getting started, while advanced students work with the SCADA Designer.
- Processor-controlled double busbar modules — Each bay has its own Ethernet interface, remotely controllable disconnect switches and circuit breakers, integrated current and voltage measurement, and programmable interlocking logic. Manual operation on the hardware remains possible.
- Line model for 150 km and 300 km overhead lines — The resistance, inductance and capacitance of a high-voltage overhead line are replicated. Students measure the voltage drop as a function of real and reactive power, quantify line losses and simulate short circuits and ground faults.
- Digital protective relays for selective power system protection — Students set the parameters of time-overcurrent relays either in analog form or via software and, in the event of a fault, selectively disconnect only the affected line section. The relationship between selectivity and grid availability becomes measurable.
- SCADA for PowerLab — The control room visualizes the grid, remotely controls disconnect switches and circuit breakers, monitors measured values at every node, parameterizes protective relays and uses the integrated soft PLC to program custom switching sequences.
- SCADA Designer for custom user interfaces — In the graphical editor, students design their own system displays and operator controls. Using the integrated soft PLC, they program interlocks and automatic switching operations that act directly on the hardware.

From Knowledge Comes Capability.
You guide the learning
Where theory and practice go hand in hand.
RXLea brings a new way of learning: project-based, hands-on and clearly structured. Learners solve real-world tasks, while instructors save time on preparation. Interactive modules, smart analytics and real hardware create a modern, efficient learning world.
Hands-on and interactive
Animations, interactive tasks and realistic scenarios build a deep understanding. All content is organized into clear learning paths for focused, hands-on learning.
Digital support
3D assembly animations and digital instructions simplify complex procedures, reduce errors and help learners work more independently.
Visual support
Overview graphics, screenshots and sample animations make the learning world transparent. Photos from the learning packages are also available, including country-specific versions where needed.




Stay ahead in
technical training.
Get the latest training systems, product launches and educational insights, delivered directly to your inbox.